A folding (bifold) door threshold comes in three practical forms: a standard raised sill, a low-profile sill and a recessed or flush sill set into the floor. Raised sills give the most water resistance. Recessed sills give the cleanest floor transition. Low-profile sills sit between the two. The right choice depends on exposure to rain, the floor build-up, and whether the opening must meet accessibility rules.
This guide explains how each option works, what drainage it needs, which U.S. height limits apply, and what to settle with the architect, builder and door manufacturer before the slab is poured.
TL;DR
- Three threshold families cover most folding door projects: raised (standard), low-profile, and recessed (flush) with integrated drainage.
- Under the ADA, thresholds on accessible routes are limited to 1/2 inch in new construction. Anything above 1/4 inch must be beveled.
- A flush sill only performs if the slab, the drain path and the waterproofing are planned with the door. Decide the sill type before the structural pour.
- Exposure matters more than style: covered patios tolerate flush sills more easily than open, wind-driven locations.
- Viewlux builds custom aluminum folding doors factory-direct and can quote the sill detail with the door.
Table of Contents
- What a folding door threshold does
- The main threshold options compared
- How thresholds manage rain and drainage
- U.S. accessibility limits that shape the choice
- How to choose: six decision points
- Planning a flush or low threshold in a new build or remodel
- Perspective
- Viewlux folding doors and sill planning
- Common questions about folding door thresholds
- Sources
What a folding door threshold does
The threshold is the base of the door frame. It carries the track for the folding panels, sheds water, seals against air and defines the step, or lack of one, between inside and outside.
A folding door is a demanding case. The panels hang from or roll on a track, they stack to one side, and the joints between panels are many. Water has more places to go than on a single swing door. The sill therefore does two jobs at once: it guides hardware and it manages water.
HUD’s Fair Housing Design Manual describes the same trade-off at any exterior door. Limited level changes are permitted because thresholds help prevent water infiltration, yet abrupt changes can impede wheelchair users and create trip hazards. The manual recommends minimizing the rise and considering interlocking or near-level solutions where feasible. Every option below is a different balance of those two goals.
The main threshold options compared
| Option | Typical profile | Floor transition | Water management | Best suited to |
|---|---|---|---|---|
| Standard raised sill | Visible upstand above the finished floor | Noticeable step | Highest margin against wind-driven rain | Exposed elevations, coastal or storm-prone sites |
| Low-profile sill | Reduced upstand, often beveled | Small, ramp-friendly rise | Good, with a sloped sill and weather seals | Most residential patios and balcony doors |
| Recessed / flush sill | Track set into the slab or floor build-up | Level or near-level | Depends on integrated drainage and slab detailing | Indoor-outdoor living, accessible routes, covered areas |
The profile names vary between manufacturers, so ask for the actual dimensions of the sill above and below the finished floor rather than relying on the label.
Standard raised sill
A raised sill places the track above the floor line. The upstand acts as a dam: water must rise over it before it reaches the interior. It is the most forgiving option when the installation is exposed to heavy rain and wind, or when the floor build-up cannot be changed.
The cost is the step. For a wide folding opening meant to feel like a removable wall, a visible upstand interrupts the line of the floor and is a trip point when carrying items through. On projects with accessibility requirements, a raised sill usually needs a ramp or has to be reduced.
Low-profile sill
A low-profile sill keeps a small upstand but reduces its height and slopes its edges. It is a common compromise for custom homes and remodels: the rise is small enough to roll over or step across, yet the sloped face and gasketed bottom rail still give a defined water barrier.
Because the sill is shallower, it is easier to align with a finished floor, and it is the usual first option when a raised sill is too tall but the slab cannot be recessed.
Recessed or flush sill
A flush sill places the track inside the floor build-up so that the walking surface runs continuously from interior to exterior. Water is handled by a drainage channel, weep paths and a sloped substrate beneath the track, not by height.
This option delivers the seamless look that luxury indoor-outdoor projects ask for, but it moves the work upstream. The structural slab needs a recess or a step-down. The exterior surface has to slope away from the door. The waterproofing has to run into the sill pan. Details for drainage specifications are covered in the Viewlux guide to flush sill drainage specs that prevent slab rework.
How thresholds manage rain and drainage
A folding door sill works on a simple principle: assume water will get into the track, then give it a controlled way out. The common elements are:
- Drainage channel. The track forms a shallow channel that collects water that passes the panel seals.
- Weep or drain openings. Water exits through openings in the sill, directed to the exterior.
- Bottom seals and gaskets. Panels carry brush or compression seals that resist air and water at the sill.
- Sloped sill or substrate. The surface under and outside the track falls away from the building.
- Sill pan or flashing. A waterproof layer under the sill directs any water that gets past the track to the exterior.
A raised sill relies more on height and less on the drain. A flush sill relies completely on the drain and on the surrounding detailing. If the exterior paving is level with the sill, or falls toward the door, a flush sill is working against the site. A small drop in the exterior surface, a slotted drain outside the door, or an overhang above all improve the odds.
For aluminum sill detailing, including how the profile, thermal break and drainage fit together, the Viewlux aluminum door threshold detail guide for builders goes further into the build-up.
U.S. accessibility limits that shape the choice
When a folding door is part of an accessible route, such as a commercial entrance, a multifamily unit or any project subject to accessibility standards, threshold height is regulated.
The Access Board’s guidance on entrances states that the ADA limits threshold height to 1/2 inch in new construction, and that edges above 1/4 inch must be beveled. Existing or altered thresholds may be as high as 3/4 inch if beveled on each side no steeper than 1:2.

The general rule for changes in level comes from the Access Board’s building blocks chapter: vertical changes up to 1/4 inch are allowed, changes from 1/4 to 1/2 inch must be beveled no steeper than 1:2, and anything above 1/2 inch must be ramped.
In practice:
- A true flush sill clears every limit with the most margin.
- A well-designed low-profile sill can meet the 1/2 inch limit if its beveled edges are within the stated slope.
- A conventional raised sill generally does not, unless the project qualifies for an exception or a ramp is built.
Verify the requirements that apply to your project with the local building department and the project’s accessibility consultant. The federal text is a baseline: state codes and the specific occupancy type can change what applies. Viewlux also publishes a builder-focused reference on ADA threshold height rules.
How to choose: six decision points
1. Exposure of the opening
A covered patio with an overhang and a drained terrace is a good candidate for a flush sill. An open balcony on a windward elevation is a case for a low-profile or raised sill with robust seals. If the opening faces prevailing storms, give weather performance priority over the last inch of floor continuity.
2. Floor build-up and slab
A flush sill needs depth. If the structural slab is already poured, the choice narrows to what can be recessed in the topping or finish layers. For new builds, the sill should be specified before the structural drawings are issued. This single coordination step prevents most flush sill problems.
3. Exterior surface and drainage
Check how the exterior paving slopes, where the water goes, and whether a drain or gap exists at the sill line. Decks, pavers and stone terraces each need a different edge detail.
4. Accessibility obligations
If the route is accessible, start from the 1/2 inch limit and work backward. Residential single-family projects have more freedom, but many owners choose a low or flush sill for aging in place and for step-free movement of strollers, carts and furniture.
5. Panel weight and track type
Large glass panels weigh more, and the track must carry them. Whether the door runs on a bottom track or hangs from a top track changes how the sill is built, and a top-hung system may allow a simpler floor detail. Panel count, stack direction and opening width should be settled alongside the sill. The Viewlux custom aluminum door configurations guide explains how those choices interact.
6. Maintenance
Any track collects dust, grit and leaves. Flush channels are easy to clean when they are open and accessible, and they should be cleaned periodically so the drain path stays clear. Raised sills are simpler to see and to sweep. Ask for cleaning guidance with the door.
Planning a flush or low threshold in a new build or remodel
New build. Involve the door supplier at schematic design. Share the finished floor level, the exterior surface level, the slab edge and the waterproofing approach. Request a sill section drawing to coordinate with the architect and the waterproofing subcontractor.
Remodel. Measure the existing floor build-up in the rough opening, including subfloor, underlayment and finish. If a recess is not possible, a low-profile sill avoids chasing the structure. In older homes, confirm the framing below the sill is sound before committing to a lower detail.
Sequence. Set the order of work: structural slab, waterproofing, sill pan, door frame, then final exterior surface. A sill installed after the paving is finished rarely drains properly.

Documentation. Keep the product’s performance ratings and the manufacturer’s installation instructions in the submittal package. Viewlux products carry NFRC and AAMA certifications, which builders and inspectors can reference in the submittal.
Perspective
Threshold decisions are made late on many projects and paid for early. A homeowner picks a bifold door for the open feel, and the sill detail only comes up when the slab is already poured. We see the same pattern repeatedly.
Our position is simple. Specify the sill with the door, not after it. A flush threshold is an engineering decision as much as a design one, and it works when the slab recess, the drain path and the waterproofing are drawn together.
Because Viewlux sells factory-direct, builders and architects speak with the manufacturer about the sill section before production, not through a chain of intermediaries. That shortens the loop between the drawing and the door, and it is how a custom aluminum folding system arrives matching the opening instead of being adapted on site.
Our claim of savings up to 50% against traditional dealers applies to the same specification: premium aluminum, custom sizing and certified performance, delivered at direct pricing.
Liran
Viewlux folding doors and sill planning
Viewlux manufactures custom aluminum folding (bifold) doors for residential and commercial projects, with custom sizing, multiple color and glass options, and flush or performance sill options across its product range. Each system is built through a 26-step production process and carries NFRC and AAMA certifications.
Builders, architects and homeowners who are specifying a project can review the folding (bifold) door page and request a quote that includes the sill detail for the opening.

The full range, including sliding, swing, pivot and panoramic systems, is listed in the Viewlux catalog. If an opening is wide and a folding door is one of several candidates, the comparison of accordion doors and bifold doors covers sizes and differences, and the aluminum sliding doors page covers the alternative with a different track layout.
Common questions about folding door thresholds
These points come up most often when owners and builders compare options.
Can a bifold door have a completely flush threshold?
Yes, when the track is recessed into the floor build-up and drainage is integrated. A flush sill depends on the slab recess, a sloped exterior surface and a sill pan. Plan these before construction, and confirm the details with the door manufacturer.
What is the maximum threshold height for an accessible folding door?
In new U.S. construction the ADA limits thresholds to 1/2 inch, and edges above 1/4 inch must be beveled. Existing or altered thresholds may reach 3/4 inch when beveled on each side no steeper than 1:2. Check local code and the project’s accessibility requirements before final selection.
Is a low-profile threshold enough for rainy or windy locations?
Often yes, provided the sill is sloped, the bottom seals are in good condition and the opening is protected by an overhang. For fully exposed, wind-driven locations, a higher sill gives more margin. A conversation with the manufacturer about the exposure helps pick the right balance.
When should the threshold type be decided?
Before the structural slab or floor build-up is finalized. Flush and recessed sills need space below the finished floor, and changing the decision after the pour limits the choices to a low-profile or raised sill.
Does the threshold affect the door’s energy performance?
The sill is part of the thermal and air-sealing envelope, so its design, thermal break and seals matter. Ask for the certified performance ratings of the complete door system, which Viewlux provides under its NFRC and AAMA certifications.
Sources
- Fair Housing Act Design Manual, Chapter 4 (HUD)
- Chapter 4: Entrances, Doors, and Gates (U.S. Access Board)
- Chapter 3: Building Blocks (U.S. Access Board)
