Standing on the secure side of the door, hinges on your left mean a left-hand (LH) door, hinges on your right mean a right-hand (RH) door, and if the leaf swings toward you instead of away, it’s a reverse swing: LHR or RHR. These four codes, LH, RH, LHR, and RHR, cover every standard configuration used in the United States. Handing affects which hardware fits and, in some buildings, which direction the code requires the door to swing.
TL;DR:
- Tell suppliers both the letter code and hinge side plus swing direction, and clarify whether their “to/from” notation means standard or reverse swing.
- Confirm whether the lockset, closer, and strike are handed or universal; an LHR door may require an RH closer body, not a matching code.
- Record the secure side, hinge side, and swing direction in a labeled photo, then attach it to the order rather than relying on memory.
- Many commercial egress doors must swing in the direction of travel, while individual dwelling units and spaces with small occupant loads are commonly exempt.
- Rehanding works on unfinished wood slabs, but doors with glazing, sidelites, or prefinished aluminum components are difficult to reverse cleanly and often warrant replacement.
Table of Contents
- Understanding LH, RH, LHR, and RHR
- How to check your door’s handing in five steps
- Mnemonics and a quick handing chart
- How handing changes hardware and door prep
- When building codes require a specific swing direction
- Can you change a door’s handing after the fact?
- Ordering checklist and common mistakes to avoid
- Why a consistent reference habit prevents most handing mistakes
- Get your swing door specified correctly the first time
- FAQ
- Sources
Understanding LH, RH, LHR, and RHR
Every handing determination starts from one fixed point: the secure side, also called the key side or outside. This is the side from which you would lock the door, and it has to stay the same reference every time you check, because switching sides mid-inspection is the most common source of ordering mistakes.
From the secure side, LH means the hinges sit on your left and the door swings away from you, into the room, in what the industry calls a standard swing. RH means hinges on your right with the same away-from-you standard swing. Reverse swings flip that motion: an LHR door has hinges on your left but swings toward you, and an RHR door has hinges on your right and also swings toward you.

You’ll also see inswing and outswing used on submittals and spec sheets. Outswing generally lines up with a standard LH or RH configuration, while inswing lines up with the reverse, LHR or RHR. The two naming systems describe the same physical door, so when a vendor asks for handing, give both the letter code and a plain description of hinge side and swing direction. That redundancy is what prevents a mismatched hinge mortise or a lockset that lands on the wrong edge of the slab.
How to check your door’s handing in five steps
Getting handing right takes less than a minute if you follow the same sequence every time.
- Walk to the secure side of the door. This is the side with the lock cylinder or the side facing the street, hallway, or exterior, and it’s the only reference point that counts.
- Locate the hinges. Look at whether they’re mounted on your left or your right as you face the door from that secure side.
- Open the door a few inches and watch which way it moves. If it swings away from you, into the next room or outside, that’s a standard swing. If it swings toward you, that’s a reverse swing.
- Combine the two observations into a code. Left hinges plus away swing is LH. Right hinges plus away swing is RH. Left hinges plus toward swing is LHR. Right hinges plus toward swing is RHR.
- Write it down and photograph it. Note the secure side, the hinge side, the knob side, and whether it’s inswing or outswing, then take a photo that clearly shows both the hinge barrels and the direction the leaf travels.
That photo is worth keeping even after you’ve settled on a code, because vendors and installers often ask for visual confirmation before cutting hardware or sending a replacement slab. Allegion’s field guidance notes that submittals using shorthand like “swing to” or “swing from” cause real confusion on job sites: “to” typically maps to a standard LH or RH swing, while “from” maps to a reverse LHR or RHR swing, so clarify which convention your supplier uses before you order.
Mnemonics and a quick handing chart
Two tricks help the determination stick in memory, though both have limits. The arm-as-door method has you stand with your back to the hinge side and extend the arm that matches the hinge side: if that’s your left arm, it’s an LH door. The “butt-to-butts” method has you face the hinge barrels directly and read left or right from there. Both fail the moment someone forgets which side they started on, which is why Family Handyman’s reporting on handing errors points back to the secure-side rule as the more reliable habit, confirmed with a photo rather than memory alone.
| Hinge side | Swing direction | Code |
|---|---|---|
| Left | Away (standard) | LH |
| Right | Away (standard) | RH |
| Left | Toward (reverse) | LHR |
| Right | Toward (reverse) | RHR |
Pro Tip: Label every photo with the secure side and the resulting code before it goes into a purchase order folder.
How handing changes hardware and door prep
Handing isn’t just a naming convention. It determines where a manufacturer cuts the hinge mortises, drills the knob or lever bore, and locates the strike plate, and it decides which side of the frame holds the closer body.
Hardware that typically depends on handing:
- Mortise locksets and many lever handles, which have a defined inside and outside face.
- Door closers, where an LHR door may call for an RH closer body rather than the closer matching the door’s own code.
- Hinges prepped at the factory into a specific mortise location.
- Strike plates and electronic access hardware tied to a fixed bore pattern.
Hardware that’s commonly non-handed, meaning it works either way without modification, includes many cylindrical locksets, passage and privacy sets, and standard deadbolts. The exceptions get more complicated with glass doors, sidelites, and factory-glazed units, where the glazing and mortise prep are set permanently during manufacturing and can’t be reversed on site without replacing components.
Before ordering, confirm three things with your supplier: whether the lockset and closer are handed or universal, whether the door arrives pre-mortised or ready for field prep, and whether any sidelite or glass kit locks in a specific swing. For a deeper look at how individual components interact, our door components specification guide walks through mortise types, strike locations, and hinge hardware in more detail.
Pro Tip: Ask any hardware vendor to send their handing chart along with your quote, so the prep matches your field notes exactly.
When building codes require a specific swing direction
Handing is mostly a matter of preference and layout, but swing direction sometimes isn’t optional. The IBC and NFPA require many doors used for egress, particularly in exit enclosures and higher-occupancy commercial spaces, to swing in the direction of exit travel, meaning outward as people leave the building. The logic is straightforward: in an emergency, a crowd pushing toward an exit shouldn’t have to pull a door open against that flow.
Individual dwelling units are commonly exempt from this requirement, along with spaces with small occupant loads, which is why most single-family homes have no code-driven restriction on which way an interior or entry door swings. Panic hardware and exit devices used in commercial egress applications are built around outswing leaves and aren’t compatible with a door prepped for inward interior use.
If your project involves a commercial space, a multi-family common area, or any room with a posted occupant load, check with your local building authority or a licensed contractor before finalizing swing direction. Our guide on door swing direction and on-site verification covers the practical checks worth running during a walkthrough.

Can you change a door’s handing after the fact?
Converting a door’s hand is possible, but whether it makes sense depends heavily on what kind of door you’re working with.
- Remove the existing hinges from the frame and slab.
- Re-mortise the opposite edge of both the frame and the door for the new hinge location.
- Relocate the knob or lever bore to the opposite stile, patching the old hole.
- Refinish the patched areas to match the surrounding wood or paint.
- Reinstall hardware on the new hinge side and test the swing.
This process is realistic on an unfinished wood slab door with basic hardware, where patching and refinishing blend in without much trouble. It becomes far less practical on a factory-glazed door, a unit with sidelites, or anything with pre-finished aluminum components, since the glazing and mortise work is permanent and reversing it leaves visible repairs. Cost and time depend on finish matching, whether structural blocking needs to move, and whether new hardware bores align with the existing frame prep. In most of those cases, ordering a new door with the correct handing built in from the factory, or choosing a reversible product line, costs less time and looks better than converting an existing unit.
Ordering checklist and common mistakes to avoid
Before you submit an order, confirm these points in writing: secure side, hinge side, swing direction, and a labeled photo of the opening.
- Clarify whether your supplier’s “to/from” notation maps to standard or reverse swing before you finalize the code.
- Confirm whether the lockset, closer, and strike are handed or universal parts.
- Check glazing and sidelite notes separately, since these often can’t be field-reversed.
- Double-check that the code on the purchase order matches the photo, not just your memory of the site visit.
Pro Tip: Keep the labeled photo attached to the order itself, not just in a separate file, so anyone reviewing it later sees the same reference you used.
Why a consistent reference habit prevents most handing mistakes
Most handing errors we see trace back to someone checking from the wrong side, often switching between the secure side and the room side without realizing it mid-inspection. The fix isn’t a better mnemonic, it’s a boring habit: stand on the secure side every time, take the photo every time, write the code down before you leave the site. A labeled photo paired with a short written note settles disputes faster than any visual trick, and it travels well when a project passes between a homeowner, a contractor, and a manufacturer. We review handing notes and photos as part of the specification process for custom swing doors to catch mismatches before they become a return.
Get your swing door specified correctly the first time
We build custom aluminum swing doors to order, which means your handing, hinge prep, and hardware are confirmed against your field notes before anything goes into production, not adjusted after a misorder arrives. Factory-direct pricing on these systems typically runs up to 50% below traditional dealer markups, since there’s no distributor layer between our production floor and your project.

Send us your handing checklist and the labeled photo from your site visit, and we’ll confirm the configuration before your order is finalized. Browse the Element 88 swing door line or visit our full catalog to start a quote.
FAQ
What does “LH door” mean?
LH means left-hand: standing on the secure side of the door, the hinges are on your left and the door swings away from you into the room. It’s one of four standard handing codes used across the hardware industry, alongside RH, LHR, and RHR.
Are there different hinges for left and right doors?
Many standard butt hinges are non-handed and work on either an LH or RH door without modification. Handing matters more for the lockset, closer body, and factory mortise location, which are often cut for a specific side and don’t reverse easily in the field.
How do you change a door from inswing to outswing?
Converting inswing to outswing generally means removing and relocating the hinges and knob bore to the opposite side, then patching and refinishing the old cutouts. This is realistic on a simple unfinished slab but difficult or impractical on a factory-glazed or pre-finished door, where replacement is usually the better option.
Can you switch a left hand swing door to a right hand swing door?
Yes, on many doors, though it involves re-mortising the hinge side, relocating the lockset bore, and refinishing the patched areas to match. Factory-prepped or glazed doors are harder to convert this way, and ordering a new door with the correct handing is often faster and cleaner.
Sources
- Right hand vs left hand door guide — Rocky Mountain Hardware
- Indicating the active leaf — I Dig Hardware (Allegion)
- Door leaf swing direction — UpCodes
- Door hinge handing and opening direction — FSchier
